2018/04/03

乐泰LOCTITE GRADE AV 087是什么胶水?

乐泰LOCTITE GRADE AV 087是什么胶水?

乐泰LOCTITE GRADE AV 087是什么胶水?

本文来自:汉高乐泰胶水(中国)有限公司 Henkel Loctite官网 www.loctite.net/c1312.html 

以下是关于乐泰LOCTITE GRADE AV 087胶水资料用途及产品的详细报告:

  TechnicalDataSheet

    LOCTITE® GRD AV™

    KnownasLOCTITE®087™

    December-2017PRODUCTDESCRIPTION    SpecificHeat,kJ/(kg·K)    0.3LOCTITE®  GRD  AV™ provides the following product

characteristics:    Electrical Properties:

Technology    Acrylic    IDiele6c0tric3B-re,akkVd/ownStrength,    9.8ChemicalType    Dimethacrylateester

Appearance(uncured)  RedliquidLMS

Fluorescence    Positive underUVlightLMS

    TYPICALPERFORMANCEOFCUREDMATERIALComponents    One component -     AdhesiveProperties

    requiresnomixing

Viscosity    Medium    After 6 hours @22°C

Cure    Anaerobic    PrevailTorque,ISO10964:

Application    Threadlocking    LMSStrength    High    3/8 x 24 steel nuts (grade      N·m         5.7 to28.3

    2) and bolts(grade2)    (lb.in.)     (50 to250)LOCTITE®GRDAV™is usedtolockandseallargecoarse

threadednuts,boltsand studsinawidevarietyofapplications    After 24 hours @22°C

where highlockingstrengthisrequired.    BreakawayTorque,ISO10964:

    3/ 8and bolts(grade2)x 24 steel nuts (grade      (Nl·.min           (70)

Mil-S-22473E    PrevailTorque,ISO10964:    LMS

    ®    3/8 x 24 steel nuts (grade      N·m         11.3 to28.3LOCTITE  GRD AV™ is tested to the lot requirements of    2) and bolts(grade2)    (lb.in.)     (100 to250)MilitarySpecificationMil-S-22473E.Note: Thisisaregional

approval.PleasecontactyourlocalTechnicalServiceCenter

formoreinformationandclarification.

ASTMD5363    TYPICALENVIRONMENTAL RESISTANCE

EachlotofadhesiveproducedinNorthAmericaistestedto    Curedfor 72  hours @22°C

the general requirements defined in paragraphs 5.1.1 and

5.1.2andtotheDetailRequirementsdefinedinsection5.2.    BreakawayTorque,ISO10964:

    3/8x 24steelnuts(grade2) and bolts(grade2)

TYPICALPROPERTIESOFUNCUREDMATERIAL

 SpecificGravity@ 25°C    1.07

 FlashPoint-SeeSDS

 Viscosity,CannonFenske, ISO3104,mPa·s(cP)    100 to250LMS

TYPICALPROPERTIESOFCUREDMATERIAL

 PhysicalProperties:

  CoefficientofThermalExpansion,    100×10-6

  ISO11359-2,K-1

  CoefficientofThermalConductivity, ISO8302,    0.1

  W/(m·K)

    TDSLOCTITE®GRDAV™,   December-2017HotStrength    Where aqueous washing systems are used to clean theTestedattemperature    surfaces before bonding, it is important to check for

    100    compatibility of thewashingsolutionwiththeadhesive.  In

    somecasestheseaqueouswashescanaffectthecureandC    performanceoftheadhesive.

  ° 75

  2

  2    Thisproductisnotnormallyrecommendedforuseonplastics@    (particularlythermoplasticmaterialswherestresscrackingofh    theplasticcouldresult). Usersarerecommendedtoconfirmt  50

  g    compatibilityoftheproductwithsuchsubstrates.

  n

  e

  r

  t

  S 25

    Directionsforuse:

  %    ForAssembly

    1. Forbestresults,cleanall surfaces(externalandinternal)

    0    ®

    0    50    100    150    withaLOCTITE cleaningsolvent andallowtodry.

    Temperature, °C    2. Ifthematerialisaninactivemetalorthecurespeedistoo

    slow,spray all threadswith Activator 7471™ or 7649™

    and allow todry.

    3. Shaketheproductthoroughlybeforeuse.

    4. Tlolopretventtthtetpruocdhuctfrtolmsclfoagcgingdinrithgeanpopzlizcle,ido.not

    5. ForThruHoles,applyseveraldropsoftheproductonto

    theboltatthenutengagementarea.

HeatAging    6. ForBlindHoles,applyseveraldropsoftheproductdownAgedattemperatureindicatedandtested @22°C    theinternalthreads tothebottomofthehole.

    7. ForSealingApplications,applya360°beadofproduct

    100    totheleadingthreadsofthemalefitting,leavingthefirst

    thread free. Force the material into the threads toC

  °    °C

    150     thouroughlyfillthevoids.Forbiggerthreadsandvoids,2    adjustproductamountaccordinglyandapplya360°bead

    75    ofproductonthefemalethreadsalso.

  @

  h    8. Assembleandtightenasrequired.

  t

  g

  n 50

  e    ForDisassembly

  r

  t    204

    °C    1. Apply localizedheatto nutorbolt  to approximately 250S

  l    °C. Disassemblewhilehot.

  a

  i  25

  t

  i

  In    ForCleanup

  %    230 °C    1.

    0    Curedproductcanberemovedwithacombinationof

    0    200    400    600    800    1000    soakinginaLOCTITE solventandmechanicalabrasion®

    Exposure Time, hours    suchasawirebrush.

    LoctiteMaterialSpecificationLMS

Chemical/SolventResistance    LMSdated September-01,1995. TestreportsforeachbatchAgedunderconditionsindicatedandtested @22°C.    areavailablefortheindicatedproperties. LMStest reports

    %ofinitialstrength    includeselectedQCtestparametersconsideredappropriatetoEnvironment    °C    300h    specificationsforcustomeruse. Additionally,comprehensiveMotoroil(MIL-L-46152)  93    100    controls  are in place to assure product quality andPhosphateester    93    100    consistency. SpecialcustomerspecificationrequirementsmayWater    93    110    becoordinatedthroughHenkel Quality.

Ethyleneglycol    93    110    Storage

Ethanol    22    115    Storeproductintheunopenedcontainer inadry location.Acetone    22    115    Storageinformationmaybeindicatedontheproductcontainer

    labeling.

    OptimalStorage: 8°Cto21°C. Storagebelow 8°CorGENERALINFORMATION    greaterthan28°CcanadverselyaffectproductpropertiesThisproductisnotrecommendedforuseinpureoxygen    Materialremovedfromcontainersmaybecontaminatedduringand/oroxygenrichsystemsandshouldnotbeselectedas   use. Donotreturnproducttotheoriginalcontainer.  Henkelasealantforchlorineorotherstrongoxidizing materials.    Corporationcannotassumeresponsibilityfor productwhich

    hasbeencontaminatedorstoredunderconditionsotherthanForsafehandlinginformationonthisproduct,consultthe   thosepreviouslyindicated.Ifadditionalinformationisrequired,SafetyDataSheet(SDS).    please contact your local Technical Service Center or

    CustomerServiceRepresentative.

Henkel Americas    Henkel Europe    Henkel AsiaPacific+860.571.5100    +49.89.320800.1800    +86.20.3623.0506

    Forthemostdirectaccesstolocalsalesandtechnicalsupportvisit:www.LOCTITE.NET    TDSLOCTITE®GRDAV™,   December-2017Conversions

(°Cx1.8)+32=°F

kV/mmx25.4=V/mil

mm/25.4=inches

µmx/02.5.4=mlbil

N/mmx5.71=lb/in

N/mm²x145=psi

MPax145=psi

N·m x 8.851= lb·in

N·mx0.738=lb·ft

N·mm x0.142=oz·in

mPa·s=cP

Note:

TheinformationprovidedinthisTechnicalDataSheet(TDS)includingthe

recommendationsforuseandapplicationoftheproductarebasedonour

knowleadgeaanadrieextperienicffeerofttheapprolidautcitasattheeldlateodfifthiisnTgDaSp.pTlihetipornodaunct

workingconditionsinyourenvironmentthatarebeyondourcontrol.Henkelis,

therefore,notliableforthesuitabilityofourproductfortheproductionprocesses

andconditionsinrespectofwhichyouusethem,aswellastheintended

arpiplictraitilosntsoacndfiresultsc.Wsueitstriloitnyglyfrercopmromduecntd.thatyoucarryoutyourown

AnyliabilityinrespectoftheinformationintheTechnicalDataSheetoranyother

writtenororalrecommendation(s)regardingtheconcernedproductisexcluded,

exceptifotherwiseexplicitlyagreedandexceptinrelationtodeathorpersonal

inrjouryucctaliuasbeilditybylaowu.rnegligenceandanyliabilityunderanyapplicablemandatory

IncaseproductsaredeliveredbyHenkelBelgiumNV,HenkelElectronic

MaterialsNV,HenkelNederlandBV,HenkelTechnologiesFranceSASand

HenkelFranceSApleaseadditionallynotethefollowing:

IncaseHenkelwouldbeneverthelessheldliable,onwhateverlegalground,

Henkel’sliabilitywillinnoeventexceedtheamountoftheconcerneddelivery.

Inisccalasiemperroidsuactsliacraebdlee:liveredbyHenkelColombiana,S.A.S.thefollowing

TheinformationprovidedinthisTechnicalDataSheet(TDS)includingthe

recommendationsforuseandapplicationoftheproductarebasedonour

knowledgeandexperienceoftheproductasatthedateofthisTDS.Henkelis,

thnereforne,itniotliabilerfosrthetsoufitawbilityhofoouurupsrodtuhctfo,rthsewprollductiothnepriotceesses

applicationsandresults.Westronglyrecommendthatyoucarryoutyourown

priortrialstoconfirmsuchsuitabilityofourproduct.

AnyliabilityinrespectoftheinformationintheTechnicalDataSheetoranyother

ewxrittepntoifrootraelrreiscomexmpelincditalytion(rs)eregaanrddienxgcthpeticnorncleartnioendtporoddeuacttisrexclusded,

injurycausedbyournegligenceandanyliabilityunderanyapplicablemandatory

productliabilitylaw.

IncaseproductsaredeliveredbyHenkelCorporation,ResinTechnology

Group,Inc.,orHenkelCanadaCorporation,thefollowingdisclaimeris

aphplicaatble:ntainedhereinarefurnishedforinformationonlyandarebelievedto

bereliable.Wecannotassumeresponsibilityfortheresultsobtainedbyothers

overwhosemethodswe havenocontrol.It istheuser'sresponsibilityto

determinesuitabilityfortheuser'spurposeofanyproductionmethodsmentioned

hrereinrtanadntoofadorpstosnuschgpriecatutioynhsaasrdmsatyhabtemaadyviseabilevflovrethienptrotehcatiodnlinof

andusethereof.Inlightoftheforegoing,HenkelCorporationspecifically

disclaims allwarrantiesexpressedorimplied, includingwarrantiesof

merchantabilityorfitnessforaparticularpurpose,arisingfromsaleoruse

ofsclaimsanyliabilityforconsequentialorincidentaldamagesofanykind,Henkel Corporation’s products. Henkel Corporation specifically

including lost profits. The discussion herein of various processes or

compositionsisnottobeinterpretedasrepresentationthattheyarefreefrom

dominationofpatentsownedbyothersorasalicenseunderanyHenkel

rCeocroporationndthateachprospectiveusertesthisproposedapplicationbeforepatents that maycoversuch processesor compositions. We

repetitiveuse,usingthisdataasaguide.Thisproductmaybecoveredbyoneor

moreUnitedStatesorforeignpatentsorpatentapplications.

Trademarkusage: [Exceptasotherwisenoted]Alltrademarksinthisdocument

aretrademarksand/orregisteredtrademarksof Henkel anditsaffiliatesinthe

U.S.andelsewhere.

ReferenceN/A

Henkel Americas    Henkel Europe    Henkel AsiaPacific+860.571.5100    +49.89.320800.1800    +86.20.3623.0506

    Forthemostdirectaccesstolocalsalesandtechnicalsupportvisit:www.LOCTITE.NET